Precision measuring for shops and unusual cars

Measure a vehicle

Everything is measured on the floor from two chalk lines, so nothing depends on holding a tape in the air. Checks run as you type.

Measuring your own car, and it's in our list? The quick version takes about 10 minutes with a tape measure.

About 45 minPlumb bobTape measureChalk lineHeight stick Quicker with mat photos

1

The vehicle

A lowered car or an aftermarket bumper is its own variant.

needed
Parts you're measuring for
Everything (all steps)
2

Set up the car

Every number is measured from the floor, so the floor and the car have to be in their normal state.

needed

For every part

How to measure3 steps

Phone (level)

  1. Park on level concrete: check the door sill at four points with the phone level; more than 1° is rejected.
  2. Set the tyres to their normal pressure and the wheels straight ahead.
  3. Note whether the bumpers and suspension are stock, and photograph each bumper.

Checked:Sill level within 1° at all four pointsYear, make, model and trim entered

3

Mark the axle lines and centreline

All measurements use one frame: the floor under the centre of the front axle, x forward, y to the left.

needed

For Front tyre spats (wheel deflectors), Radiator cooling duct plates, Brake cooling inlet plates, Side skirt winglets +8 more

How to measure5 steps

Plumb bobChalk line or masking tapeTape measure

  1. Drop the plumb bob from the centre of each front hub and mark the floor; snap a chalk line between the marks.
  2. Do the same at the rear hubs.
  3. Mark the middle of each axle line and snap the centreline between them.
  4. Measure the wheelbase (front to rear axle line) and both track widths (hub mark to hub mark).
  5. For roof, trunk and tailgate parts, also measure the overall length, the width without mirrors, the height to the roof, and each overhang (axle line to the bumper face). Without them these parts are placed on an estimated body.

Checked:Wheelbase within 3/8 in of the manufacturer figureCentreline square to the axle lines (3-4-5 check)

4

Ride height

Records lowered or lifted cars: ground clearance depends on it, and it makes the car its own variant.

needed

For every part

How to measure1 step

Height stick

  1. Measure from the floor to the top of each wheel arch, straight above the hub, at all four corners.

Checked:Left and right within 1 in of each otherEach corner between 10 and 60 in

Read dots from mat photos

The quick way: stick dots on the printed mats, photograph them, and the tables below fill themselves.

optional

About 1 mmPhotos stay on this device Mats: Letter · A4 · how to lay them

How to lay the mats and take the photos4 steps
  1. 1Print at 100% and measure the 200 mm check line on one mat.
  2. 2Lay datum A on the chalk-line crossing, arrow forward. Chain the other mats out under the edge, each touching a neighbour.
  3. 3Plumb-bob down and stick a red dot per outline point, a blue dot per mounting point.
  4. 4Shoot from about 1 m up, phone flat. Two whole mats per photo; every mat shares a photo with a neighbour, back to datum A.
Drop mat photos hereor
5

Trace the front bumper lip

The splitter and chin lip follow this edge exactly.

needed

For Front splitter, Chin lip, Splitter end plates (air dams), Front air dam (valance) +4 more

How to measure3 steps

Plumb bobRed dotsHeight stickTape measureMarker mats (optional)

  1. Drop the plumb bob from the lowest edge of the bumper every 2 in, and at every corner and change of curve, from one wheel arch to the other. Stick a red dot where it touches.
  2. For each dot, enter how far it is in front of the front axle line (x), how far left (+) or right (−) of the centreline (y), and the height of the lip above it (z).
  3. Work from the left end to the right end.

Checked:At least 12 points, no gap over 4 inBoth sides of the centreline coveredLeft and right halves mirror within 3/16 in

0 complete points

Paste from a spreadsheet

6

Trace the rear bumper lip

The diffuser hangs from this edge and follows it.

needed

For Rear diffuser, Rear valance (bumper skirt)

How to measure2 steps

Plumb bobRed dotsHeight stickTape measure

  1. Drop the plumb bob from the lowest rear edge of the bumper every 2 in, left end to right end.
  2. Enter each dot as for the front: x is negative (behind the front axle), y left positive, z the height.

Checked:At least 10 pointsEvery point behind the rear axle line

Rear points are behind the rear axle: x is below −wheelbase.

0 complete points

Paste from a spreadsheet

7

Trace the rockers

Side skirt blades follow the outer lower edge of each rocker.

needed

For Side skirt extensions, Side skirt winglets, Flat floor panel

How to measure2 steps

Plumb bobRed dotsHeight stickTape measure

  1. Drop from the outer lower edge of the left rocker every 4 in, from the front arch to the rear arch, then do the right.
  2. If only one side can be measured the other is mirrored, with a warning.

Checked:At least 6 points a sideLeft and right mirror within 1/4 in

Left rocker (y positive)

0 complete points

Paste from a spreadsheet

Right rocker (y negative)

0 complete points

Paste from a spreadsheet

8

Front tyres at full lock

Splitters, undertrays and skirts must clear the tyres when steering.

optional

For Front splitter, Chin lip, Front undertray, Front air dam (valance) +2 more

How to measure2 steps

Chalk or dotsTape measure

  1. Turn the wheel to full left lock and mark the floor under the front and inside edges of both front tyres; repeat at full right lock and straight ahead.
  2. Enter the marks around each tyre as one outline (6–12 points).

Checked:Each outline near its wheelOutline closed and not self-crossing

Enter the points in order around the swept area; the outline must not cross itself.

Left front tyre

0 complete points

Paste from a spreadsheet

Right front tyre

0 complete points

Paste from a spreadsheet

9

Front bumper corner at canard height

Canards are cut to sit flush against the curved corner.

needed

For Canards (dive planes)

How to measure2 steps

Profile gaugeCardHeight stick

  1. Mark the canard height on the left front corner with tape; measure its height from the floor.
  2. Press the profile gauge level against the corner at that height, trace the shape onto card, and enter the traced points in the car frame (or photograph the card on a marker mat).

Checked:At least 6 pointsCurve starts on the front face and wraps round the side

Plan-view outline of the left front corner at canard height, front face round to the side.

0 complete points

Paste from a spreadsheet

10

Mounting points

Holes are cut exactly over these; a part is only as good as its mounts.

needed

For Front splitter, Chin lip, Front undertray, Side skirt extensions +10 more

How to measure3 steps

Plumb bobNumbered blue dotsHeight stickThread gauge card

  1. Drop from every bolt, clip, tow-hook mount and frame hole that could carry the part; stick a numbered blue dot.
  2. Enter its position (x, y), its height (z), its thread from the gauge card, and which parts it can carry.
  3. Photograph each point from below with its number visible.

Checked:Left/right pairs within 1/4 in of the same heightThread identified (unknown is cut for M8 with a warning)

Still needed for:
splitterundertrayskirtmudflapfloordiffuserskid-engineskid-transmissionskid-transferskid-tankskid-diffskid-arm

11

Things to avoid or reach

Tow hooks, sensors, drain plugs, filters and exhaust tips need holes, notches or clearance.

optional

For Front splitter, Chin lip, Splitter end plates (air dams), Canards (dive planes) +12 more

How to measure2 steps

Plumb bobTape measure

  1. For each one, drop to its centre, enter its position and radius, and choose: avoid it, cut a hole for it, or leave access to it.
  2. Mark exhaust tips as hot: plastics and plywood are kept at least 3 in away.

Checked:Each keep-out has a radius over 0.25 in

Radius, not diameter. Tick Hot for exhaust tips.

12

Cross-check with a tape

Two tape measurements the guide can predict catch a wrong dot, a wrong sign or a misread tape.

needed

For every part

How to measure2 steps

Tape measure

  1. The guide picks two distances from your measurements (for example lip corner to lip corner, and a mount to the axle line).
  2. Measure them with the tape and enter them. More than 1/8 in out and that step must be redone.

Checked:Both within 1/8 in

Nothing to check yet
Enter a traced edge and two mounting points; the tape checks are picked from them.

Send the measurements

Send what you have: parts that need the rest stay blocked until it's measured.