Fitplate for shops · aero and underbody protection

Splitters, diffusers and skid plates
cut to the car on your lift.

Measure the car once with printed mats and your phone, size each part, and every piece is checked for tyre sweep, ground clearance and keep-outs before it is cut. You get flat parts, the hardware list and install steps.

  • 33 part types
  • Optional fit sample on unverified cars
  • One DXF per piece

Start here

From your floor to cut parts, in order

Try every part on the example cars now. To order, measure your car: steps 2 and 3.

Try the example car

Every part, check and price works on the two example vehicles. They can’t be ordered.

2 minNothing to measure
Open the example

Print the marker mats

15 sheets of plain paper at 100%.

Letter or A415 pages
Print the mats

Precision measuring

For unusual or modified cars: chalk two lines, lay the mats, stick dots, photograph. Cars in our list can skip it.

About 45 minPhone
Start measuring

Configure on your car

Your car joins the vehicle list once the measurements are sent. Add parts and size them.

33 part types
Open the configurator

Fit sample or straight to the parts

Order a thin polypropylene copy of each main piece to test-fit first, or skip it and request the quote straight away.

Fit sampleQuote in 1–2 days

Parts

Everything below the bodywork

Front

Front splitter

Flat plate under the front bumper, following its exact shape, with support rods and splice plates.

ACM aluminum composite, 0.236" · ABS plastic, 0.234" · ABS plastic, 0.187" · Baltic birch plywood, 0.472" · Baltic birch plywood, 0.354" · 6061 aluminum, 0.250" · 5052 aluminum, 0.187" · Carbon fiber, 0.197" · Carbon fiber, 0.157" · HDPE marine board, 0.375" · HDPE marine board, 0.250"

Configure

Chin lip

Narrow flexible blade along the bumper lip: the street-friendly splitter.

ABS plastic, 0.234" · ABS plastic, 0.187" · ABS plastic, 0.125" · HDPE marine board, 0.375" · HDPE marine board, 0.250" · ACM aluminum composite, 0.236"

Configure

Splitter end plates (air dams)

Vertical plates at the splitter ends that seal the air under the car.

ACM aluminum composite, 0.118" · Carbon fiber, 0.157" · Carbon fiber, 0.118" (3 mm) · Carbon fiber, 0.197" · 5052 aluminum, 0.125" · 5052 aluminum, 0.090" · ACM aluminum composite, 0.236" · ABS plastic, 0.187" · ABS plastic, 0.125"

Configure

Canards (dive planes)

Small flat wings on the bumper corners, cut to follow the corner shape.

Carbon fiber, 0.157" · Carbon fiber, 0.118" (3 mm) · Carbon fiber, 0.197" · ABS plastic, 0.187" · ABS plastic, 0.125" · 5052 aluminum, 0.125" · 5052 aluminum, 0.090" · ACM aluminum composite, 0.118"

Configure

Front undertray

Flat panel from the bumper back to the subframe: a smooth floor under the engine bay.

ABS plastic, 0.234" · ABS plastic, 0.187" · ACM aluminum composite, 0.236" · HDPE marine board, 0.375" · 5052 aluminum, 0.125" · 5052 aluminum, 0.090" · Baltic birch plywood, 0.354"

Configure

Front air dam (valance)

Vertical blade hanging under the front bumper, cut in straight sections that follow its curve. Cuts lift and drag on trucks, SUVs and vans.

ABS plastic, 0.187" · ABS plastic, 0.234" · ABS plastic, 0.125" · HDPE marine board, 0.250" · HDPE marine board, 0.375" · ACM aluminum composite, 0.118" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Front tyre spats (wheel deflectors)

Small vertical plates just ahead of the front tyres that turn the air round them. Left and right.

ABS plastic, 0.187" · ABS plastic, 0.125" · ABS plastic, 0.234" · HDPE marine board, 0.250" · ACM aluminum composite, 0.118" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Radiator cooling duct plates

Side plates and a floor that seal the gap between the bumper opening and the radiator, so all the air goes through it.

ACM aluminum composite, 0.118" · ABS plastic, 0.125" · ABS plastic, 0.187" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Brake cooling inlet plates

Flat plates for a bumper or fog-light opening with a round spigot hole for brake cooling hose. Left and right.

5052 aluminum, 0.090" · 5052 aluminum, 0.125" · ABS plastic, 0.187" · ACM aluminum composite, 0.118" · Carbon fiber, 0.118" (3 mm)

Configure

Licence plate relocation bracket

Bent bracket that moves the front plate off the splitter or air dam: to the side, or onto a bumper bolt.

5052 aluminum, 0.125" · 5052 aluminum, 0.090" · Mild steel, 0.074" · 304 stainless steel, 0.060"

Configure

Side

Side skirt extensions

Flat blades under the rockers that keep air from rolling under the car. Left and right.

ABS plastic, 0.234" · ABS plastic, 0.187" · ABS plastic, 0.125" · ACM aluminum composite, 0.236" · ACM aluminum composite, 0.118" · HDPE marine board, 0.375" · HDPE marine board, 0.250" · Carbon fiber, 0.197" · Carbon fiber, 0.157" · 6061 aluminum, 0.250" · 5052 aluminum, 0.125"

Configure

Side skirt winglets

Small vertical fins hanging under the rear end of each side skirt, angled to push air out past the rear tyres. Left and right.

ABS plastic, 0.187" · Carbon fiber, 0.157" · Carbon fiber, 0.118" (3 mm) · ACM aluminum composite, 0.118" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Mud flaps

Rally-style flaps behind the wheels, in HDPE or UHMW.

HDPE marine board, 0.375" · UHMW plastic, 0.375" · HDPE marine board, 0.250" · HDPE marine board, 0.500" · UHMW plastic, 0.500" · ABS plastic, 0.187"

Configure

Flat floor

Flat floor panel

Flat panel under the middle of the car, between the front undertray and the diffuser.

ABS plastic, 0.187" · ABS plastic, 0.125" · ACM aluminum composite, 0.236" · ACM aluminum composite, 0.118" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125" · HDPE marine board, 0.250"

Configure

Rear

Rear diffuser

Panel under the rear bumper with slot-in strakes. Exhaust tips get heat-cleared notches.

ACM aluminum composite, 0.236" · ABS plastic, 0.234" · ABS plastic, 0.187" · 5052 aluminum, 0.125" · 5052 aluminum, 0.090" · Carbon fiber, 0.197" · Carbon fiber, 0.157" · 6061 aluminum, 0.250"

Configure

Rear valance (bumper skirt)

Vertical blade under the rear bumper, in straight sections, notched round the exhaust tips.

ABS plastic, 0.187" · ABS plastic, 0.234" · ABS plastic, 0.125" · HDPE marine board, 0.250" · HDPE marine board, 0.375" · ACM aluminum composite, 0.118" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Ducktail (trunk lip spoiler)

Bent aluminum lip along the rear edge of the trunk lid.

5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Flat-plate rear wing

A flat aluminum wing plate with a bent gurney on its trailing edge, for the wing uprights.

5052 aluminum, 0.125" · 5052 aluminum, 0.090" · 5052 aluminum, 0.187"

Configure

Wing end plates

Replacement end plates for an existing rear wing.

Carbon fiber, 0.157" · Carbon fiber, 0.118" (3 mm) · Carbon fiber, 0.197" · 5052 aluminum, 0.125" · 5052 aluminum, 0.090" · 5052 aluminum, 0.187" · ACM aluminum composite, 0.118"

Configure

Wing uprights

Flat aluminum uprights (standard or swan-neck) for a rear wing.

6061 aluminum, 0.250" · 5052 aluminum, 0.250" · 5052 aluminum, 0.187"

Configure

Wing mount backing plates

Plates that go inside the trunk lid (and optionally under each upright foot) to spread the wing load.

5052 aluminum, 0.125" · 5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.119"

Configure

Gurney flap

Bent aluminum strip on the trailing edge of a wing or spoiler.

5052 aluminum, 0.090" · 5052 aluminum, 0.125" · 304 stainless steel, 0.060"

Configure

Wicker bill

Angled aluminum strip riveted on top of a spoiler's or ducktail's trailing edge: a small, adjustable-feel gurney.

5052 aluminum, 0.090" · 5052 aluminum, 0.125" · 304 stainless steel, 0.060"

Configure

Tailgate spoiler

Bent aluminum lip along the top of a pickup's tailgate that tidies the air off the bed.

5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Roof

Roof spoiler

Bent aluminum spoiler at the back edge of the roof: SUVs, vans, hatchbacks and truck cabs.

5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Roof rack wind fairing

Flat fairing on the front bar of a roof rack that cuts wind noise and drag. Cars, SUVs, trucks and vans.

ABS plastic, 0.187" · ABS plastic, 0.125" · ACM aluminum composite, 0.118" · 5052 aluminum, 0.090" · 5052 aluminum, 0.125"

Configure

Underbody protection

Engine skid plate

Protects the oil pan and front of the engine; ramps up to the front crossmember when the mounts are higher there.

5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.188" · Mild steel, 0.250" · UHMW plastic, 0.375" · UHMW plastic, 0.500" · HDPE marine board, 0.500"

Configure

Transmission skid plate

Covers the transmission between the frame rails.

5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.188" · Mild steel, 0.250" · UHMW plastic, 0.375" · UHMW plastic, 0.500" · HDPE marine board, 0.500"

Configure

Transfer case skid plate

Covers the transfer case on 4x4s.

5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.188" · Mild steel, 0.250" · UHMW plastic, 0.375" · UHMW plastic, 0.500" · HDPE marine board, 0.500"

Configure

Fuel tank skid plate

Covers the fuel tank.

5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.188" · Mild steel, 0.250" · UHMW plastic, 0.375" · UHMW plastic, 0.500" · HDPE marine board, 0.500"

Configure

Rear differential skid plate

Covers the rear differential.

5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.188" · Mild steel, 0.250" · UHMW plastic, 0.375" · UHMW plastic, 0.500" · HDPE marine board, 0.500"

Configure

Control arm skids

Small plates under the lower control arms. Left and right.

5052 aluminum, 0.187" · 5052 aluminum, 0.250" · Mild steel, 0.188" · Mild steel, 0.250" · UHMW plastic, 0.375" · UHMW plastic, 0.500" · HDPE marine board, 0.500"

Configure

Front bumper skid plate

Sloped plate under a truck, SUV or van front bumper that guards the bumper's underside and smooths the air under it.

5052 aluminum, 0.125" · 5052 aluminum, 0.187" · Mild steel, 0.119" · HDPE marine board, 0.375" · UHMW plastic, 0.375"

Configure

Fabrication

The right machine for each piece

Each piece goes to the cheapest fabricator that can make it in one piece, or is split with splice plates. Numbers marked provisional are placeholders until partner shops quote.

FabricatorLargest pieceMaterialsPricingUsed for
SendCutSend44 x 30 in (carbon 44 x 23)aluminum, steel, stainless, carbon-fiber, g10, plastic, wood, acmInstantDefault for anything up to 44 x 30 in (carbon 44 x 23 in) and every fit sample. Powder coat up to 31 x 37 in.
OSH Cutprovisional118 x 46 inaluminum, steel, stainlessQuoteLarge metal parts in one piece: full-width aluminum splitters, wide skid plates.
Local CNC router shopprovisional94 x 46 inwood, acm, plasticBy the sheetOne-piece splitters, diffusers and skirts in ACM, plywood and plastics, batched by the sheet.
Local laser / waterjet shopprovisional118 x 58 inaluminum, steel, stainless, carbon-fiberQuoteBatches of large metal parts; quoted per job (roughly $60–120 per machine hour plus setup).

FAQ

Questions shops ask

Who is this for?

Tuning, alignment, off-road and fab shops that fit aero or underbody armour for customers and would rather not draw each part in CAD. You pick the vehicle, set the sizes, and get cut parts, the hardware list and the install steps.

How do the parts fit a car you have never seen?

Every part is generated from a vehicle profile: the bumper lips, rockers, tyre sweep at full lock, mounting points and keep-outs. Cars in our list start from an estimate built from published dimensions; for unusual or modified cars, the precision guide measures them with the floor-projection method. Profiles are rated example, estimated, unverified, measured (three shops agree) or verified (three confirmed installs).

What stops a bad part being cut?

Every part is checked before you can order: tyre clearance at full lock, ground clearance against your target, exhaust and sensor keep-outs, hole edge distances, bend limits and the fabricator size limits. Below verified, a polypropylene fit sample of each main piece is recommended and can be test-fitted first.

Who cuts the parts?

Pieces up to 44 x 30 in go to SendCutSend. One-piece splitters and diffusers in ACM, plywood or plastic go to a local CNC router shop by the sheet; big metal parts go to OSH Cut or a local laser shop. Large pieces can also be split with splice plates so everything ships from one place.

Is it legal on the street?

Ground clearance, overhang and sharp-edge rules vary by state and by event. The checks enforce your own minimum ground clearance; the street rules for your area are your call. Splitter rods and rigid mounts are recommended for anything that is stood on.

Do you nest the parts?

No. Fabricators nest in their own CAM software. You get one clean DXF per piece and a cut list; sheet prices from the router shop are estimates until the shop confirms them.

Start with the example car

The example profiles are complete, so every part and check works. They can't be ordered: measure your own vehicle first.

Open the configurator